Showing posts with label Steep Turns. Show all posts
Showing posts with label Steep Turns. Show all posts

Friday, August 28, 2009

Preparation for Instrument Rating Check Ride


Separate IR training into components:
- depature
- enroute
- holding
- approach
- missed
Prior to Departure do a NATSE departure briefing:
1. NOTAM / ATIS / WEATHER / Weight and Balance / Flight Plan
2. cAp: Chart date, briefing point by point, frequencies (tower, departure)
3. Terrain: MSA, which way
4. Special Notes: departure, taxiing
5. Emergencies

Pre-Taxi/Taxi/Runup:
- Brief passenger (treat exaiminer as passenger)
- Do NOT be taxiing while writing stuff down!!
- Do Taxi checks (gyros, VOR, ADF, auto-pilot)
- Before take-off, do a PTILT check (don't rush, do most of this prior to entering runway)
Pitot Heat
Time
Instruments - when lined up look at airport diagram with any variation eg. RWAY 24 might actually be 236 degrees)
Lights - throw on landing lights
Transponder - ensure transponder is on

Departure:
With every flight, copy down clearance
- ask for IFR clearance after runup
- copy down word for word
- repeat word for word
- make a note of this in your book, it makes it easier to record and read back clearance:
ATC Clears _________ (your plane)
To ________ (to airport you filed)
Route ______________ (this could be long)
Climb ____________
Contact ____________
SQUAK __________

Climbs:
- Attitude to 8 degrees, Power, then Trim
- Scan altitude, vertical speed, heading
- Give youself altitude countup -200 ft., -100 ft., -50 ft.

Level off:
- Attitude, Power, then Trim
- Start the level off -10% of VSI (eg. 400 ft/min - start level off at -40 ft. of level of alt.)
Straight and Level:
- Always Remember: Attitude + Power = Desired Performance
- Keep scan going and correct one thing at a time

Turns:
- Always turn at rate one turn: 10% of speed + 5
- Come out of turn 1/2 angle lead in rolling out to a heading.

Steep Turns (360 degrees either left or right):
- Stabilize heading and Altitude
- Do a HASEL check (turn carb off); ask exaimer to check for clearing turns
- Enter into the 45 degree turn
- Add power as you cross the 30 degree mark
- Don't allow for nose to drop
- Come out at 20 degrees prior to selected heading

Unusual Attitudes:
- Watch Airspeed: Low - FULL power; High - power OFF
- Bring wings to level
- Watch Altitude: Climb (important) or Descend

Descends:
- Power, Attitude to 2 degrees (just below line), then Trim
- Scan altitude, vertical speed, heading
- Come out of descend 10% of vertical speed (eg. 400 ft/min turn - start to level out +40 ft.)
- Give youself altitude countdown +200 ft., +100 ft., +50 ft.

When landing
- get "cleared for approach to xx airport"
- you can declare the approach you prefer (if they don't say which one)
- they will then hand you off to the tower/MF (sometimes this happens really late)
- typically you can tune in on the 2nd radio to get ATIS to notify tower/MF you are coming
- they might say "4 on the slope" - this means you have to maintain 4000 intercept

Holds
- FIRST THING TO ASK WHEN HOLD IS GIVEN IS EXPECTED CLEARANCE ARRIVAL TIME (when to leave hold)
- Pay attention to left (non-standard) or right (standard)
- ensure you have: Note time (drop dead time to get on to alternate depending on fuel requirements: Holding Time Available = Fuel - Reserve Fuel + To Alternate Fuel)
- slow down before getting into hold, take winds into consideration
- if hold is not published, you should hold on inbound track
- re. winds - you can add double surface winds and add 30 degrees to surface winds
- timing
- don't wait for NDB to go 360, begin turn when its abeam
- start outbound when you are abeam (NDB) / FROM to TO (VOR)
- start when you rollout of track to inbound
- adjust outbound so its 1 min. (under 14,000 ft.) or 1.5 min. (over 14,000 ft.)
- headwind on outbound, reduce outbound / tailwind on outbound, increase outbound
- call entering hold, call established hold

Turn Procedure
- You don't need to follow the procedure turn diagram indicated in the chart
- You can use other variations, as long as you are on the procedure turn side indicated in the chart (90 degrees + 270 degrees, or circle / 1 min. turn, 2 min. parallel typically)
- Don't blow the SAFE distance (typically 10 NM from NDB)
- (on non-standard procedure turns, start timing after crossing center line)
- Do not descend to fix altitute before inbound (intermediate leg) path to fix
- Do prelanding checks on outbound (but keep carb heat off and flaps up until approach)
- Procedure turn: call beacon inbound (for procedure turn), beacon outbound (on procedure turn), intercept ILS or NDB

Approaches
__NDB
- **can only decend to fix after intercepting final course**
- setup speeds with flap settings *prior* to intercepting fix so that you can keep track of time
- pick a speed that is favourable and *maintain* that speed throughout
- start timing after becon completes rotation
- for non-precision decend to MDA and continue at MDA height looking for runway till time runs out (so that you don't go missed prior to getting to runway sighting)
- start looking a mile back (approx 40 seconds back?)
- when circling, never loose sight of runway
- when circling, maintain the preset speed and keep bank to under 30 degrees
__ILS
- Need to be at MSA during procedure turn ; can only decend to specified altitude for approach after intercepting final approach course
- follow the approach vertical and horizontal on intercept in final approach fix - be at intercept altitude to intercept vertical ** do not decend immediatly to fix altitude (as in NDB) **
- Give youself altitude countdown +200 ft., +100 ft., +50 ft.
- don't chase needle, just make sure it doesn't move the opposite way / arrest needle moment

http://whitts.alioth.net/Pageg82%20Instrument%20Proficiency%20Review.htm
http://www.crazefamily.net/ifr_training.htm#P1L1

Other things learned:
Engine managment is must:
- start at 500 rpm and slowly increase after stablization
- lean 1 inch after startup
- power up and down gently

Communications failure: FIRST SET TRANSPONDER TO 7600

Shutdown:
- ensure that all electricals are off (so you don't have a power surge)
- starve the engine first by pulling mixture, then turn off mags

Saturday, September 04, 2004

Slow Flight, Stalls, Steep Turns:

The student is now ready to go solo to the practice area and practice slow flight, stalls, steep turns, etc. HASEL check should be done prior to these procedures.

HASEL Check

Height above 4000 ft.
Area not built up
Secure – doors/windows/seatbelts/objects
Engine – primer locked, master on, alternator on, mags both, unnecessary electrics off, oil pres./temp. green, carb hot, mixture rich, fuel on;
Lookout – 90 degree to left (look at heading indicator and stop at 90 <-) and 90 degree to right ->)

Flapless Stall Entry

Power to idle (control yaw with rudder)
Maintain Altitude by pulling back on control

Flap Stall Entry

Power to 1500 RPM
Flaps at 20 degrees, count till 7
Maintain Altitude by pulling back control

Stall Recovery:

Control – Nose down (no dives, to regain flight attitude at level, use rudder)
Power – Full Throttle, Carb Cold
Drag - Flaps UP

Spin Entry:

YAW in direction of wing drop in stall (fully stalled is prerequisite)
Only done in certified aircraft by instructor.

Spin Recovery:

In spin, the airspeed will be constant or low at stalling speed

Power OFF (Throttle to idle, carb cold, flaps off)
Control – Full opposite rudder, hold till rotation stops, control column forward (full forward might be required)
Power ON – Throttle Full, Carb Cold, Flaps off

Spiral Recovery:

In descent, airspeed, descent and wing load will be increasing

Power Off
First Neutralize Ailerons – roll wings to level
Then Pull out of dive.(otherwise it aggrevates spiral)
Apply power after airspeed down

Slow Flight Entry:

Pick a point on the nose (to try hold heading )
Reduce Power to 1500 RPM (or reduce RPM in 100 RPM stages)
Carb HOT
Trim to maintain altitude
Drop Flaps 20 degrees when airspeed in White Arc
Adjust Pitch
At desired A/S, adjust power (2000 – 2200 RPM Right Rudder) Altitude should not increase/decrease
Add power during turns
Add full power for climbs (not adjusting pitch)

Slow Flight Recovery:

Full power, right rudder, Carb COLD
Lower nose for A/S to increase
Flaps up in stages

Steep Turns:

Pick a point on the nose (so that you can come back to that point)
Note heading indicator
Make lookouts (left and right)
Roll through 30 degrees (wing strut parallel to ground)
Roll through to 45 degrees increasing power and pulling control column back
Keep horizon line on windshield constant
Don’t let altitude to drop
Roll back 20 degrees prior to start heading